Log in or Sign up
Antiques Board
Home
Forums
>
Antique Forums
>
Antique Discussion
>
Jaeger LeCoultre Clock
>
Reply to Thread
Message:
<p>[QUOTE="afantiques, post: 62789, member: 25"]Please do nor start taking it apart.</p><p><br /></p><p>No good will come of it, letting someone who refers to 'the gears' anywhere near the movement.</p><p><br /></p><p>Unless the thing has been dropped and thus had the balance staff broken, the probable reason for non running is simple disuse. Oil on the spring intended to make the coils slide over each other turns to glue, effectively removing all power to the train.</p><p><br /></p><p>I once removed a fully wound French clock spring from a barrel so gummed up that even out of the barrel it just stayed as a lump. It had not been used for about 80 years, rather longer than your clock but the principle is very common.</p><p><br /></p><p>A realistic value is more like $200.</p><p><br /></p><p>There is a rather tedious but non-invasive method that might help.</p><p><br /></p><p>I am sure it is fully wound up,so you can actually drive it from the winder. Apply some pressure to the winder and give the clock a twist in the plane of the dial to see if ticks, maintain the pressure and it may tick for a while. This is a good sign, indicating no serious problem with the balance staff.</p><p><br /></p><p>What you have to do is to sit with it in your hand, and maintaining that moderate pressure on the winder, keep it ticking for half an hour. If it becomes too boring, do it some more later.</p><p><br /></p><p>The idea of this is to let the spring run down a tiny amount, as this may break the old dry oil bond and then once the spring leaves start to move, they should be enough to run the clock.</p><p><br /></p><p>The thing will still need cleaning but allowed to run right down and rewound a few times, the old oil could be disturbed enough to allow normal running.</p><p><br /></p><p>In general this technique will work on most old spring clocks and watches that have sat idle for a long time. It is not a substitute for a proper overhaul but it is hard for a repairer presented with a working clock for a simple clean to 'discover' some expensive fault when they have you over a barrel.[/QUOTE]</p><p><br /></p>
[QUOTE="afantiques, post: 62789, member: 25"]Please do nor start taking it apart. No good will come of it, letting someone who refers to 'the gears' anywhere near the movement. Unless the thing has been dropped and thus had the balance staff broken, the probable reason for non running is simple disuse. Oil on the spring intended to make the coils slide over each other turns to glue, effectively removing all power to the train. I once removed a fully wound French clock spring from a barrel so gummed up that even out of the barrel it just stayed as a lump. It had not been used for about 80 years, rather longer than your clock but the principle is very common. A realistic value is more like $200. There is a rather tedious but non-invasive method that might help. I am sure it is fully wound up,so you can actually drive it from the winder. Apply some pressure to the winder and give the clock a twist in the plane of the dial to see if ticks, maintain the pressure and it may tick for a while. This is a good sign, indicating no serious problem with the balance staff. What you have to do is to sit with it in your hand, and maintaining that moderate pressure on the winder, keep it ticking for half an hour. If it becomes too boring, do it some more later. The idea of this is to let the spring run down a tiny amount, as this may break the old dry oil bond and then once the spring leaves start to move, they should be enough to run the clock. The thing will still need cleaning but allowed to run right down and rewound a few times, the old oil could be disturbed enough to allow normal running. In general this technique will work on most old spring clocks and watches that have sat idle for a long time. It is not a substitute for a proper overhaul but it is hard for a repairer presented with a working clock for a simple clean to 'discover' some expensive fault when they have you over a barrel.[/QUOTE]
Your name or email address:
Do you already have an account?
No, create an account now.
Yes, my password is:
Forgot your password?
Stay logged in
Antiques Board
Home
Forums
>
Antique Forums
>
Antique Discussion
>
Jaeger LeCoultre Clock
>
Home
Home
Quick Links
Search Forums
Recent Activity
Recent Posts
Forums
Forums
Quick Links
Search Forums
Recent Posts
Gallery
Gallery
Quick Links
Search Media
New Media
Members
Members
Quick Links
Notable Members
Registered Members
Current Visitors
Recent Activity
New Profile Posts
Menu
Search
Search titles only
Posted by Member:
Separate names with a comma.
Newer Than:
Search this thread only
Search this forum only
Display results as threads
Useful Searches
Recent Posts
More...